Adrian Flux - 0800 916 1257

Mitsubishi Delica Owners Club UK™
Mitsubishi Delica L300, L400 and D:5 Owners Club
 
 FAQFAQ   SearchSearch   Watched TopicsWatched Topics   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your personal messagesLog in to check your personal messages   Log inLog in 
CalendarCalendar  dynamic online chat serviceChatrooms   Delica Club ShopClub Shop  MDOCUK Classified Ads serviceClassified Ads
MDOCUK home pageMDOCUK Home  Yellow Diamond ClubsYellow Diamond Clubs  Delica Club (CA)Delica Club (CA)  Delica Club (AUS)Delica Club (AUS)

fitting towbar : ?captive nut/self retained nut for chassis


 
Post new topic   Reply to topic    Mitsubishi Delica Owners Club UK™ Forum Index -> Towing & technical
View previous topic :: View next topic  
Author Message
richard_co



Joined: 09 Nov 2016
Posts: 12
Location: uk

PostPosted: Mon Jun 11, 2018 17:49    Post subject: fitting towbar : ?captive nut/self retained nut for chassis Reply with quote

Hello

Pretty new Delica owner with only basic mechanical skills hoping to do stuff myself.

Looked through all the towing and technical posts and can't find an answer to this so sorry if its obvious or dim:

I bought a towbar from a breakers yard off ebay for my facelift Delica.  it looks pretty straightforward basically two arms each with 4 holes.  2 holes in each arm look like they receive a bolt through the side walls of the rear part of the chassis and then there's a plate at right angles with 2 holes which looks like it should bolt to the underside of the chassis.  The problem is with these latter holes, where it looks like it should bolt in, there's not a huge access (just a small square gap) adjacent to the hole for trying to stop the nut spinning round whilst trying to tighten the bolt.  

Looking on the Anker instructions they mention 'cage nut' which fits through the square hole and clips in to it holding the bolt captive over the chassis hole so the towbar can then be bolted on.  Unfortunately the towbar didn't come with any fittings and anker don't sell the fittings independently.

So firstly am I right that this is how the towbar bolts to the underside of the chassis? if so does anyone know how where i can get hold of this sort of captive nut i can't find anything really similar on the internet though don't in all honestly know exactly what it would be called?  Alternatively is there any relatively simple work around? Or alternatively am I just being a bit dim and missed the point completely?

Thanks
Richard
Back to top
View user's profile Send personal message
Google
Sponsor





PostPosted: Mon Jun 11, 2018 17:49    Post subject: Google Ads keep this community free to join!


Back to top
Lewis
Site Admin


Joined: 25 May 2006
Posts: 16291
Location: Huddersfield

PostPosted: Mon Jun 11, 2018 20:16    Post subject: Reply with quote

The 'cage nut' on the Anker fitting is just a nut welded to a short length of flat bar, over a hole in the bar, for the bolt to go through. That is slipped inside the chassis, through one of the adjacent cut outs, so you can hold the bar and position the nut over where the bolt goes through, whilst you bolt it in. Then the bar jams against the inside of the box section, holding it firmly in place whilst you tighten the bolt up.

There are some photos of one in position on this post:- http://www.MDOCUK.co.uk/forums/viewtopic.php?t=38846

The Cage nut fitting is used at the top of the angled bar shown in the bottom photo. Note that one end of that long bar has a square spacer block fitted at one end. That goes at the bottom against the angled bracket. Re the second last photo.

HTH
_________________


Copyright is retained for all my photos. Please don't copy them without asking permission
Do not blindly go where the path may lead you. Go where there is no path and leave a trail that others may follow!
ルイス
Back to top
View user's profile Send personal message Visit poster's website
richard_co



Joined: 09 Nov 2016
Posts: 12
Location: uk

PostPosted: Mon Jun 11, 2018 21:32    Post subject: Reply with quote

Thanks Lewis
That's really useful, I've a friend who I hope can knock up some of those for me.  Since you're around on the subject the vertical towbar plate that is held against the chassis will overlap the recovery loop on the left hand side, which bulges slightly. presumably you can't remove the recovery hoop, the towbar just gets bolted against the recovery hoop.

don't know whether that makes sense?

Thanks Richard
Back to top
View user's profile Send personal message
Lewis
Site Admin


Joined: 25 May 2006
Posts: 16291
Location: Huddersfield

PostPosted: Tue Jun 12, 2018 0:43    Post subject: Reply with quote

I assume you are referring to two towing eyes ?

I had an Anker towbar on my previous Deli and neither eye was covered by the towbar brackets. Both of those should be vertical in alignment. If one is bent back a bit, presumably from a previous owner doing some towing, or a snatch recovery using them, then just bend it back straight, with a wrecking bar.

You could remove them, ( with an angle grinder ) if you wish to, as the towbar becomes the recovery strap fixing point.

HTH
_________________


Copyright is retained for all my photos. Please don't copy them without asking permission
Do not blindly go where the path may lead you. Go where there is no path and leave a trail that others may follow!
ルイス
Back to top
View user's profile Send personal message Visit poster's website
Display posts from previous:   
Post new topic   Reply to topic    Mitsubishi Delica Owners Club UK™ Forum Index -> Towing & technical All times are GMT + 1 Hour
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


All contents © Hobson's Choice IT Solutions Ltd 1997 on
Powered by phpBB © 2001, 2005 phpBB Group